View YB1506_4127462.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

YB1506
Step-up DC-DC Converter , White LED Driver Description
The YB1506 is a step-up(Boost) DC-DC converter; operate as current source to drive up to 5 white LEDs in series. Series connecting of the LEDs provides identical LED currents resulting in uniform brightness and eliminating the need for ballast resistors. The light intensity of these LEDs is proportional to the current passing through them. The low off-time permits the use of tiny, low profile inductors and capacitors to minimize footprint and cost in space consideration applications for cellular phone backlighting or other hand held equipment. The YB1506 can drive up to 5 white LEDs from a single Li-Ion battery DC 2.2V to 6.5V; can be turn on by putting more than 1.2 volt at pin 4 (SHDN). To control LED brightness, the LED current can be pulsed by applying a PWM (pulse width modulated) signal with a frequency range of 100Hz to 50KHz to the SHDN pin.YB1506 has integrated Over Voltage Protection that prevents damage to the device in case of a high impedance output due to faulty LED.
Features
Internal switch Adjustable output voltage up to 22V 2.2V to 6.5V input range 0.1uA shutdown current Small 5-Lead SOT-23 package High efficiency Drives 5 white LEDs Over voltage protection
Applications
LCD Display Module White LED Backlighting PDAs Digital Cameras Portable Application Cellular Phone Electronic books
Typical Application Circuit (Li-Ion battery 2.5 volt to 6.5 volt is recommended.)
Figure 1 Typical Application Circuit
YB1506 MRev1.1
WWW.YOBON.COM.TW
1
YB1506
Step-up DC-DC Converter , White LED Driver Pin Description
Figure 2
YB1506 SOT23-5
Pin Designator
Table 1 :
Pin 1 2
NAME SW GND
Description
Switching Pin. This is the drain of the internal NMOS power switch. Connect to inductor and diode. Minimize the metal trace area connected to this pin to reduce EMI. Ground Pin. Connect directly to local ground plane. Feedback Pin. Set the WLED current by selecting value of R1 using:
3
FB
I LED
=
0.4V R2
4 5
SHDN
VIN
Shutdown Pin. The shutdown pin is an active low control. Tie this pin above 0.9V to enable the device, below 0.6V to turn off the device. Input Supply Pin. Bypass this pin with a capacitor as close the device as possible.
Ordering Information
Table 2:
Order Number YB1506
Package Type SOT23-5
Supplied as 3000 units Tape & Reel
Package Marking Y56
YB1506 MRev1.1
WWW.YOBON.COM.TW
2
YB1506
Step-up DC-DC Converter , White LED Driver Absolute Maximum Retings
Vin 7V SW voltage 28V FB Vin Vin+0.3V SHDN Maximum Junction Temp,Tj 150 C (note 2) Lead Temperature (Soldering 10 300 C Thermal Resistance 195 C
Absolute Maximum Retings
Operating Temperature -40 ~ +85 C (note 3) Supply Voltage 2.2V~6.5V Maximum SW Voltage 22V
sec)
Electricity Characteristics
Table 3 : (TA=25C , Vin=3V unless otherwise noted)
Symbol VIN IQ (Quiescent Current) VFB ICL IB ILKG TOFF TON RDS(ON) ISD UVP OVP
SHDN Threshold
Function Parameter Input Voltage Range Not Switching Shutdown Feedback Voltage Switch Current Limit FB Pin Bias Current SW Leakage Current Switch Off Time Switch On Time Switch RDS(ON)
SHDN PIN Current
Test Conditions FB = 0.5V
SHDN =0V
Min 2.2
Typ 70 0.1
Max 6.5 90
Units V uA V mA nA uA nS uS nA V V V /W
0.38 350 FB=2V VSW=20V
0.4 450 30 0.05 350 4 0.7
0.42 550 120 0.1 400 1.6 80
Input Under-Voltage Protection Output Over-voltage Protection SHDN Low SHDN High Thermal Resistance
SHDN =GND or Vin ON-OFF Threshold
1.6 22.5 0.9 220 23.5
2.0 24.5 0.6
JA
Note 1. 2.
3.
Absolute maximum ratings are limits beyond which damage to the device may occur. The maximum allowable power dissipation is a function of maximum function temperature , TJ(max), the junction to ambient thermal resistance, JA , and the ambient temperature. The maximum allowable power dissipation at any ambient temperature is calculated using: PD(MAX)= [TJ(max)-TA]/JA . Exceeding the maximum allowable power dissipation will cause excessive die temperature. All limits at temperature extremes are guaranteed via correlation using standard statistical methods
YB1506 MRev1.1
WWW.YOBON.COM.TW
3
YB1506
Step-up DC-DC Converter , White LED Driver Typical Performance Characteristics
YB1506 MRev1.1
WWW.YOBON.COM.TW
4
YB1506
Step-up DC-DC Converter , White LED Driver Function Block
Figure 3 Function Block
Application Information
The YB1506 features a constant off-time control scheme. The Housekeeping provides a bandgap reference used to control the output voltage. When the voltage at the FB pin is less than trip point, the input comp amplifier enables the device and the NMOS switch is turned on pulling the SW pin to ground. When the NMOS switch is on, current begins to flow through inductor L while the load current is supplied by the output capacitor Cout. Once the current in the inductor reaches the current limit, the CL Comp trips and the timer turns off the NMOS switch. The inductor current will now begin to decrease. At the same time, the energy stored in the inductor transferred to Cout and the load. After the 400ns off time the NMOS switch is turned on and energy is stored in the inductor again.
Inductor Selection
The appropriate inductor for a given application is calculated using the following equation:
- VIN, MIN + VD V L = OUT I CL TOFF
Where VD is the schottky diode voltage, ICL is the switch current limit found in the Typical Performance Characteristics section, and TOFF is the switch off time. When using this equation be sure to use the minimum input voltage for the application, such as for battery-powered application.
Choosing inductor with low ESR decrease power losses and increase When FB reaches the trip point, the input efficiency. comp amplifier then disables the device and turns off the NMOS switch. The SHDN pin can be used to turn off the device. In the shutdown mode the output voltage will be a diode drop lower than the input voltage.
YB1506 MRev1.1 WWW.YOBON.COM.TW 5
YB1506
Step-up DC-DC Converter , White LED Driver Diode selection
To maintain high efficiency, the average current rating of the schottky diode should be large than the peak inductor current, IPK. Schottky diode with a low forward drop and fast switching speeds are ideal for increase efficiency in portable application. Choose a reverse breakdown of the schottky diode large than the output voltage. effect input voltage ripple of the IC. For additional input voltage filtering, a 100nF bypass capacitor can be placed in parallel with Cin to shunt any high frequency noise to ground. The output capacitor, Cout, should also be placed close to the IC. Any copper trace connections for the Cout capacitor can increase the series resistance, which directly effect output voltage ripple. The feedback network, resister R2 should be kept close to the FB pin to minimize copper trace connections that can inject noise into the system. The ground connection for the feedback resistor network should connect directly to an analog ground plane. The analog ground plane should tie directly to the GND pin. If no analog ground plane is available, the ground connection for the feedback network should tie directly to the GND pin. Trace connections made to the inductor and schottky diode should be minimized to reduce power dissipation and increase overall efficiency.
Capacitor selection
Choose low ESR capacitors for the output to minimize output voltage ripple. Multilayer capacitors are a good choice for this as well. A 4.7uF capacitor is sufficient for most applications. For additional bypassing, a 100nF ceramic capacitor can be used to shunt high frequency ripple on the input.
Layout consideration
The input bypass capacitor Cin, as shown in Figure 1, must be placed close to the IC. This will reduce copper trace resistance which
Figure 4
20V Application
YB1506 MRev1.1
WWW.YOBON.COM.TW
6
YB1506
Step-up DC-DC Converter , White LED Driver LED Current Control
The LED current is controlled by the feedback resistor (R1 in Figure 1). The feedback reference is 400mV. The LED current is 400mV/R1. In order to have accurate LED current, precision resistors are preferred (1% is recommended). The formula and table for R1 selection are shown below. R1 = 95mV/ILED
Table 4. R1 Resistor Value Selection
ILED(mA) 20 15 10 5 1
R1() 20 26.6 40 80 400
of brightness control is a variable DC voltage to adjust the LED current. The dimming control using a DC voltage is shown in Figure 5. As the DC voltage increases, the voltage drop on R2 increases and the voltage drop on R1 decreases. Thus, the LED current decreases. The selection of R2 and R3 will make the current from the variable DC source much smaller than the LED current and much larger than the FB pin bias current. For VDC range from 0V to 2V, the selection of resistors in Figure 5 gives dimming control of LED current from 0mA to 15mA. 3. Using a Filtered PWM Signal The filtered PWM signal can be considered as an adjustable DC voltage. It can be used to replace the variable DC voltage source in dimming control. The circuit is shown in Figure 7.
Dimming Control
There are four different types of dimming control circuits: 1. Using a PWM Signal to SHDN Pin With the PWM signal applied to the SHDN pin, the YB1506 is turned on or off by the PWM signal. The LEDs operate at either zero or full current. The average LED current increases proportionally with the duty cycle of the PWM signal. A 0% duty cycle will turn off the YB1506 and corresponds to zero LED current. A 100% duty cycle corresponds to full current. The typical frequency range of the PWM signal is 1kHz to 10kHz. The magnitude of the PWM signal should be higher than the minimum SHDN voltage high. 2. Using a DC Voltage For some applications, the preferred
YB1506 MRev1.1
4. Using a Logic Signal
For applications that need to adjust the LED current in discrete steps, a logic signal can be used as shown in Figure 6. R1 sets the minimum LED current (when the NMOS is off). RINC sets how much the LED current increases when the NMOS is turned on. The selection of R1 and RINC follows formula (1) and Table 4.
WWW.YOBON.COM.TW
7
YB1506
Step-up DC-DC Converter , White LED Driver
Figure 5
Dimming Control using a DC voltage
Figure 6
Dimming Control using a LOGIC SIGNAL
Figure 7
Dimming Control using a PWM
YB1506 MRev1.1
WWW.YOBON.COM.TW
8
YB1506
Step-up DC-DC Converter , White LED Driver APPLICATION EXAMPLE
Figure 8
Two White LEDs Application in Li-Ion Battery
Figure 9
Three White LEDs Application
Figure 10
YB1506 MRev1.1
Four White LEDs Application
WWW.YOBON.COM.TW 9
YB1506
Step-up DC-DC Converter , White LED Driver SOT-25 Package Information
All the contains in this datasheet are not assuming any responsibility for use of any circuitry described, no circuit patent license are implied and Yobon reserves the right at any time without notice to change said circuitry and specifications. Yobon Inc. would like to receive your feedback with your recommends and suggestions, that is always welcome and with our appreciations.
YB1506 MRev1.1
WWW.YOBON.COM.TW
10

▲Up To Search▲

Price & Availability of YB1506

	To Download YB1506 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .